Sharp Opening Service Mode
Sharp Opening Service Mode
Method 1
1. INPUT + POWER button and plug ac CORD
2. Tingnan yung nindicator ligths na mag blink yung red at green.
3. Press UP DOWN UP channel BUTTON
4. press INPUT BUTTON
Then lalabas yung service mode.
5. Then go to page 9 look for lamp error na naka set sa 5 prees ENTER sa remote magiging zero, after maging zero press 1 sa remote, tas magiging white nalng yung display.
6. Unplug AC cord
After 3 minutes plug in AC CORD.
Comments
-
Method 2 for Single Button
Smode : Press hold center button, then plugged ac cord. Once led indicator blink, released button.
input password:
Single, single, hold press.
Pagdating sa selection , gamitin ang joystick sa remote at select service mode then press center ng joystick.
Dapat less thas 30 second para makapasok.
0 -
Method 3
- hold Input at volume down sabay then plug AC cord
- "K" will appear in upper Left Position of Screen
- hold Channel Down at volume down sabay then lalabas na ung adjustment
0 -
Method 4
1.Press and hold power and center button then plugged AC cord sa wall outlet.
2. Unpress button kung nagblinking na ng green/red/green/red ang led indicator then enter password:
3. Password: Ch up, Ch down, Ch up and screen become purple.(plain raster).
Hold press center button for about 5seconds ang wait service mode appear on screen.
0 -
chassis 11AK 45 B5 29 MF 92 ERU
login - In operating mode, press the MENU 4 7 2 5
Chassis 5BS-A 54AT-15SC
login - Hold down the keys (VOL-) and (CH +) panel TV turn on the TV network switch.
Exit - POWER OFF
Model 21D1, 21D2 Proc. IX3368CE (TDA9381):
login - Close jumper JA137 and JA138 for a short time while in operation.
Exit from
the regime - once again short-circuit jumper. The jumpers are located
to the left of the video processor, beneath the oval slot in the
motherboard.
chassis DA100
login - Hold the VOL-and CH + in front of the TV turn on the network button.
output - Turn off the TV network button.
Chassis VP-2 VT-1428M, VT-2128M
login
- Install the TV in standby mode and press the button on the remote in
the sequence CH UP for more than 2 seconds and simultaneously press
POWER.
Exit - (MENU)
model14D-SC, 14B-SC, 20B-SC, 14D-CM, 21D-CK1, CV-2132CK1 percent. IX1704CENI
login - On board TV, set the S1008 in the position of the service mode.
output - S1008
model 14R-SC/M8/M10, 14R-W, CV-14RU, 21FN1
login - On board TV, set the S1006 in the position of the service mode.
Chassis SP-70 21FN1 Proc. IX2938CEN2
login - Set the switch S1006 to the position of the service mode.
To
display on the screen one by one mode, press the key S-MODE, S-NORM on
the remote, change the value of the keys on the remote up, down.
output - S1006
Chassis SP-42M 25FN1, 29FN1 Proc. M37210M4-775SP
login
- On board TV, set the S1001 in the position of the service mode. To
display on the screen one by one mode, press the key S-MODE button on
the remote control.
output - S1001
Chassis 5BS 37/54AM-12SC, 37/54M-16SC, 37/54AM-23SC Proc. IX1572BMNO (SDA20561-A529)
login - Hold down the keys (VOL-) and (CH +) panel TV turn on the TV network switch.
output - (MODE)
Chassis SC 63CS-03SC, 70CS-03SC, 70AS-05S. percent. SAB-S502
login - Hold down the keys (VOL-) and (CH +) panel TV turn on the TV network tumbler
output - (STANBY)
Chassis CA-1 54DT-25SC, 54DT-26SC Proc. IX1655BMN1, IX1669BMNO (SDA5222)
login - Hold down the keys (VOL-) and (CH +) panel TV turn on the TV network switch.
output - (MENU)
Chassis D3000 DV-25071S
login - Click on the S1401 switch is located in the module RWB-B
output - Click on the S1401 again.
Chassis SP-51 14/21JN1
login - To enter the menu to apply +5 volts to 37 foot of the processor.
Chassis BCTV-A DV-5935H Proc. SAB8032
login
- Install a jumper between terminal 2 (body) and pin 6 (SV) are located
on the signal board TV. Turn on your TV and remove the jumper.
output Put a jumper. Off. TV, remove the jumper.
Chassis EURO-DS1 DV-5101H DV-5103H Proc. CCU3000
login - Install a jumper between terminal 2 (body) and pin 6 (SV) are located on the signal board TV.
output Press (SKIP) on the remote. Remove the jumper switch off your TV.
DV-5403S DIGITAL
login - On-board digital module color momentarily close contacts "Tools" near the top chip KM6264BLG-10.
Exit - A second time to close these contacts.
0